Programming mode in PSoC 1

Questions about programming (not codeing) PSoCs and Encore II as well as freeware programming hardware and software are discussed here. This is also the place to talk about production programming. Programming means loading a HEX file in to the Flash, not, writing your program.

Moderator: ericb

Programming mode in PSoC 1

Postby Tanisha » Thu Nov 22, 2012 11:42 pm

There are 2 programming modes in PSoC 1 - Reset & Power Cycle. What is the difference between the two? Is there a strategy to decide which option would be best for our design?
Tanisha
Newbie
Newbie
 
Posts: 2
Joined: Thu Nov 22, 2012 11:36 pm

Re: Programming mode in PSoC 1

Postby bobmarlowe » Sun Nov 25, 2012 8:41 am

When your PSoC-board is powered by external supply you have to use reset-mode. When you power the PCB with your miniprog you may choose any method as far as you did not connect the xres-pin to some circuitry which will inhibit resetting. There is no advantage from any method neither is there any coding requirement.

Bob
User avatar
bobmarlowe
The Big Cheese
The Big Cheese
 
Posts: 1490
Joined: Thu Oct 06, 2011 2:03 am
Location: Germany

Re: Programming mode in PSoC 1

Postby anshul » Sun Nov 25, 2012 9:37 pm

Hi Tanisha,

Use the Reset programming mode when the device is powered by an external source and use Power cycle mode if your device is powered from your programmer (MiniProg1, MiniProg3 etc.).

For more details about the programming modes, you can refer page 2 of the "Introduction to Programming" App Note which can be downloaded from the link http://www.cypress.com/?docID=39607

Regards
Anshul
anshul
Newbie
Newbie
 
Posts: 5
Joined: Sun Nov 25, 2012 9:06 pm

Re: Programming mode in PSoC 1

Postby anshul » Mon Nov 26, 2012 2:01 am

Reset mode - Use this mode when the device is powered from an external source
power-cycle mode - Use this mode when the programmer like MiniProg1, MiniProg3 etc. powers this device.

For more details on the programming modes, you can refer to the page 2 of the Application Note "Introduction to Programming" which can be downloaded from the link http://www.cypress.com/?rID=2726.

Thanks
Anshul
anshul
Newbie
Newbie
 
Posts: 5
Joined: Sun Nov 25, 2012 9:06 pm

Re: Programming mode in PSoC 1

Postby Tanisha » Mon Nov 26, 2012 5:22 pm

Thanks Bob and Anshul
Tanisha
Newbie
Newbie
 
Posts: 2
Joined: Thu Nov 22, 2012 11:36 pm

Re: Programming mode in PSoC 1

Postby bobmarlowe » Mon Nov 26, 2012 11:39 pm

You are always welcome!

Bob
User avatar
bobmarlowe
The Big Cheese
The Big Cheese
 
Posts: 1490
Joined: Thu Oct 06, 2011 2:03 am
Location: Germany

Re: Programming mode in PSoC 1

Postby granel » Sat Mar 02, 2013 2:00 am

Hi, I have question : can MiniProg1 change PowerSettings 3,3V or lower?
I can set only 5 V.
3,3V can set only with jamper CY3210 + power adapter.
But need to work only with notebook , without outside power , power set +3,3V.
User avatar
granel
Cheese Wheel
Cheese Wheel
 
Posts: 74
Joined: Tue Feb 19, 2013 11:54 am
Website: http://www.g-e.ee/.
Location: Estonia


Return to “%s” Device Programmers

Who is online

Users browsing this forum: No registered users and 1 guest